![]() ![]() Note: The default wireless security is the WiFi password of front router.ĩ. You can set the WiFi name and password, or use the default settings, and click. Choose the WiFi signal that you like to extend. Or go to Administration > Operation mode, select Repeater mode and click to apply settings.ĥ. ![]() When you login to the Web GUI for the first time, you will be automatically directed to the Quick Internet Setup (QIS) page. Note 2: Default WiFi name (SSID) shown on the product label on the back side of the device.ģ. Note 1: The default URL for some models is Connect your computer to the RP-AX58 via WiFi connection and enter your RP-AX58 LAN IP(like ) or URL to the Web GUI. Check the front-end device (router or modem) can connect to the Internet and has the WiFi function.Ģ. Please download and Install the Device Discovery Utility first. Note: In repeater mode, the DHCP-assigned IP address changes. The wireless range extender will not distribute IP. Note: In this mode, the firewall, IP sharing and NAT functions are disable by default, so the IP addresses obtained when wireless devices connect to the wireless range extender are all assigned by the DHCP server of the front router/modem. Again, just make sure that the SSID and passwords match the settings on your existing router.How to set Repeater mode on the ASUS wireless range extender?(WebGUI)ĪSUS range extender supports several operation modes to meet different requirements, please refer to the product specification page to confirm that your device supports the above features.ĪSUS range extender is in repeater mode by default, and in repeater mode, the ASUS range extender can wirelessly connect to an existing wireless networks from front modem/router to extend the wireless coverage and provide better signal strength for users. Most modern extenders will have settings for both a 2.4GHz network and a 5GHz network. Once it’s logged in and the connection is stable, it will rebroadcast the same data connection on the same SSID throughout your home, allowing for easy connections via other devices. What’s happening is that the extender is logging into your network via the router, just like you do with your laptop or phone. But if it doesn’t (for example, if you bought your extender used), here’s what you do: Michael Crider/IDGįind the Wi-Fi settings page for your extender, and enter the same name for the SSID and password as you use with your Wi-Fi router. Once you’re logged into the repeater interface, it should start a wizard to guide you through connecting to your local network step-by-step. If the default name and password don’t work, try a factory reset of the device, which usually needs a button pressed with a pin or paperclip. Don’t worry, you can change them later in the extender settings menu. These are usually “admin” and “password,” respectively. Once you get to this page, you’ll need to log in with the default username and password. If you can’t find it, Google your repeater brand on your phone and add “login,” and you’ll probably find it soon enough. My Netgear extender uses “some Asus models use “,” et cetera. ![]() If neither of those addresses work, check the instructions that came with your extender or the sticker printed on its side some brands use something a little different. Try entering both of those in the URL bar a login prompt should appear. The address for this interface is usually a simple numerical address on the local network, either 192.168.0.1 or 192.168.1.1. You’re going to use the browser to enter the extender’s web-based interface. On your computer, open a web browser like Edge or Chrome. If there’s a switch on the side of your extender, make sure it’s set to “Extender” mode, not “AP” or “Access Point.” (AP is for connecting directly to your modem, which you don’t need if you have a Wi-Fi router already, or an all-in-one modem/router.) It may need a few minutes to boot up. ![]() Note that in both cases you’ll temporarily lose web connection. Alternately, disconnect from your home Wi-Fi network and connect directly to the extender. Plug the extender into the wall, then plug the Ethernet cable into both the extender and your computer. Michael Crider/IDGĬonnecting a laptop to the Wi-Fi extender. (One probably came in the box with your extender.) If your computer doesn’t have an Ethernet port, you’ll need to connect to the default Wi-Fi network that the extender broadcasts, which is different from the one already in your home (at least for now.) This is usually “WIFI_EXTENDER” or something similar check the instructions if it asks for a password. You’ll need a desktop or laptop with an Ethernet cable for a wired connection, and the cable itself. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |